Click on an image for a larger version.
Local pickup is fine if you're in the Warrnambool, Victoria (Australia) area, otherwise postage/freight is at your own expense
Sorry, I won't do "Including postage" offers, I've been burnt too many times by excessive postage costs...
Be sure to check back occasionally, as I'm adding and removing items to this list often!
Look, a Box!
Large Aluminium box 55cm(l) x 35cm(w) x 38cm(h). Once used as a transit case for an IFR 1200S service monitor.
GME DIN mounting plate
GME DIN mounting adaptor
Philips FM93 microphone NOS
Microphones to suit the Philips FM93 model radio. These mics have an internal preamp, but it can easily be removed & the mic modded to work with other radios. I've got quite a few of these mics if you're after more than one.
Motorola GP300 VHF handheld
2 channel with charger & Speaker mic
Motorola GP300 VHF handheld
4 channel with charger & Speaker mic
Motorola GP300 chargers
Motorola GP300 speaker microphones
ICOM IC-MB16 mounting bracket
these were suited to the IC-X16 handhelds among others
ICOM IC-U28 handhelds
two radios, one battery, one charger - UHF 16 channels
IDA DTMF Microphone
Brand new, old stock, never used. These are a good quality DTMF mic with onboard preamp & seperate adjustments for DTMF & Voice levels. I might even have a circuit diagram here somewhere too.
GME MK003B microphone clamp
i think this was for a tx6000 to clamp the speaker mic onto the top of the radio
not sure what this fits, but the label says "GME TX840", so probably that model of CB radio
e-band (66-88MHz) radio/PM843a PSU/remote leased line system. No crystals.
VHF high band handheld w/2 chargers
10 channel scanner - has had a couple of new battery contacts fitted, some battery leakage in the past has caused minor corrosion on a couple of the other battery contacts, tested ok, includes rubber duck antenna
UHF approx 450-510 MHz, 4 cavity units
Large compressed air impact driver - got a truck? change your tyres...
UHF cavity filter
UHF mini diplexer parts
$20 the lot
these are missing the tuning assemblies
Unicomp Model M keyboard - the classic indestructable keyboard
Xerox Docuprint C525A toner cartridge
black, brand new - I don't even have this printer anymore...
Xerox Phaser 860 extended maintenance kit & parts
Again, don't own the printer, don't need the parts... both the maintenance kit & clutch kit are brand new
Wavetek 12-18GHz Micro Source Microwave signal generator
model 957A - good working order
Flightstick analogue joystick
BWD 272A variable power supply
0-12V @ 2A, 0-25V @ 1A, 0-50V @ 0.5A, good working order
8 channel input interface to suit RME HDSP2496 audio interface card
NOS Water meter, calibrated in US gallons, still at 000000, calibration certificate included, never used
Hewlett Packard printer parts
$50 the lot
mostly paper feed rollers/transfer rollers from HP Laserjet printers, most unused, spares from maintenance kits
Aviation instrument test rig
apparently used to test a "Tacan", whatever that was... there's a few different RF & multi pin connectors on here. Comes in a cool box with "Rolls Royce" written on the side.
Vintage iron parts
$20 the lot
lots of bits here
Ampeg SVT II bass guitar amplifier
This is a late '80's SVT-II, an all-valve (6x6550 in the power stage) bass monster that will do 300watts into a 4 or 2 ohm load. It's recently been re-tubed & set up (probably a couple of years ago) & has sat on the shelf ever since. In excellent working order, this thing sounds amazing!
Marconi TF893A audio power meter
Sunbeam mixmaster handle
NOS spare part, has slight damage as per photo
Orion model 2012 CRT drive board
removed from an arcade machine with a faulty yoke on the CRT
probably used in an Electrolux dealership or service centre
Deltron power supply
6 amps at 20 volts, a good unit for the workshop
Response 12" sub woofer driver
dual voice coil, these things can handle huge amounts of power, brand new never used
2 x 15 element $100ea
1 x 6 element $70
ZCG Scalar Yagi antennas 480-487MHz Ruggedised stainless steel version
Icom IC-HM8 Microphone
Icom HM-8 Microphone, untested, has 8-pin DIN connection, not sure what model radio this unit suits.
Kyoritsu VU Meter
VU Meter, NOS. There's 2 of these
One for the real collectors - 500uA FSD microammeter, pretty big as you can see, good working condition, probably out of cal..
Fender Squier guitar practice amplifier
little practice amp for your guitar. works well
Roll of RG11 Quad Shield coax
RG11 quad shield 75ohm coax. 78 metres left on the roll.
18 core computer cable
18 conductor serial cable, probably about 20 metres left on the roll.
25 core computer cable
25 conductor serial cable, looks like about half the 100 metres left on the roll.
Uniden Speaker Microphone
Uniden speaker mic, untested, not sure which model radios it suits.
Tait Orca Speaker Microphones
$10 for both
Speaker mics to suit Tait Orca handhelds, untested, obviously used.
24-12V 15A voltage reducer
Arista 24-12 volt reducer. 15 amp rated.
Codan X2 microphone
Mic to suit Codan transceiver.
Uniden microphone NOS
Uniden Mic. brand new old stock, not sure which radio this unit suits, is a condenser microphone, not dynamic, so probably one of their UHF models
Ipod FM transmitter
Ipod FM transmitter, plugs into the top of your ipod, transmits to your car radio. Only works with ipods with the power connection next to the headphone jack (gen 4 has this, not sure about others)
FunCube Dongle Pro
Funcube Dongle Pro 64MHz to 1,700MHz Software Defined Radio.
Icom PCR-1000 computer controlled receiver
Icom PCR1000 receiver. good working order, not sure where the software is for this, but it's easily acquired on the internet.
A few different kits, I was going to split these up & use the parts, but someone might like them complete: 2xK8003 Voltage Controlled Dimmers, 2x K8004 DC to Pulse Width Modulator, 1 x K8001 Independent Control Module, 1 x K8000 Computer Interface Board.
HP Docking Station
Good condition, used for a nx6120 laptop, but will suit other models.
Fluke 19 Multimeter
RFI SMD4 Dipole Antenna
New old stock. 400-420MHz.
RFI Antenna spring
Bullbar mount antenna spring. Not the later q-fit unit, but the earlier type with the grub screws to hold the antenna. Model CD2199